Water Deionizer

EUROPE

Aquapro Deionizer

Aquapro Deionizer

Battery water for filling forklift truck batteries, work platforms, cars, trucks and wherever demineralized water is required quickly and cost-effectively and is to be produced in-house

Aquapro Deionizer Our cost-effective cartridge systems are simply connected to the tap to purify the water and use it directly to fill your battery. Save the cost of distilled water and make it yourself. Depending on the hardness of your location, you can produce up to 2500 litres of deionised water. the set contains everything you need. And thanks to the 3 LED display, you can always see whether the water quality is still good or not.

There are 3 different sizes, with different amounts of resin, 4.5, 7 and 12 Liter capacity Each set contains :

  • High pressure tank, filled with resin, hose connection on the inlet side (12 mm) or via ¾ ‘thread directly
  • Refillable system, only the used resin is replaced again for cost-effective battery waterin
  • Quick coupling on the outlet side (Gardena-compatible system),
  • T-piece distributor Unit, with electronic conductivity measuring system
  • 2.5 meter premium EPDM Hose + female connection coupling with filter and flow indicator,
  • Choose the easy pressure reducer (0.7 bar) option with which you can fill your batterydirectly

It will be mounted at the end of the distributor and allows direct connection to yours watering system

  • Conductivity measuring Unit
  • 3 Status LED , red, yellow, green
  • Indication of the outgoing water quality

Size : "S"

How does it work ?

The water from the tap /inlet flows (red arrow) through the cartridge, where it meets the resin and is purified. Suspended solids and mineral salts are removed, the water is purified and its electrical conductivity is reduced so that it can be used as battery water. The conductance of the water is specified in microSiemens (µS) and should not exceed a value of 10µS for lead/acid traction batteries.

All dissolved salts and ions are measured in the conductance and is therefore more accurate than a measurement of carbonate and total hardness

The maximum amount of water to be purified depends on many factors, and many manufacturers specify unrealistic quantities.

Important for you:

The hardness of the water at your location! because this essentially determines the performance of the cartridge

Know us more

Whats the benefit ?

We have deliberately opted for this type of cartridge as it is more environmentally friendly than other products on the market and you can change the resin yourself if necessary, thus avoiding disposable cartridges that pollute the environment.

The change is very simple and is explained step by step in our tutorial.

Know us more

To make it even easier for you, we offer a replacement service.

You send the used cartridge back to us, we regenerate the resin using the latest technology and send it back to you. And at an attractive price compared to our competitors’ disposable cartridges.

This is our active contribution to avoiding plastic waste, which is unfortunately growing unnecessarily. Think ecologically, avoid wasting plastic resources and help to keep our planet green.

Why ? ?

Tap water contains minerals and impurities that can be harmful to forklift batteries. These substances can cause deposits, promote corrosion, increase self-discharge and contaminate the electrolyte. All of this has a negative effect on the performance and service life of the battery. It is therefore important to use only demineralized water. This is the only way to protect the battery and extend its service life, as demineralized water does not contain any harmful substances.

by the way

The water quality is given in uSiemens or in PPM. Both describe the value of water hardness from your tap.

Our region in Bavaria, near the Alps, has excellent water for drinking, but not for filling up yours battery. The incoming value is more than 570 µSiemens and cannot be used with further treatment, the conductivity value must be reduced to approx. 10 µSiemens maximum

How many litres can i take ?

The quantity of pure water that can be achieved depends on the quality of the incoming raw water and cannot be clearly defined. If you want to compare our cartridges with other products, you should always take the quantity of resin as a comparison.

The calculator below will help you to calculate the expected capacity.

Enter the conductance of your water in μS/cm (microsiemens) in the first field. You should either measure this value or ask your water supplier for it.

You can also use a TDS meter, which can always be found cheaply on the internet.

TDS ‘Total Dissolved Solids’ represents the total amount of dissolved solids such as minerals, salts and metals in the water. This value is usually expressed in milligrams per litre (mg/l) or in PPM (parts per million) and can be converted into microsiemens μS/cm

1.2 µS/cm then corresponds to 1 ppm, which means that you have to multiply the value of the TDS meter by 1.2 in order to enter it in the field

Calculator Water

Result, Amount of Water

Excellent water with 0 Siemens = 00

Result: -- (liter)

  • Pressure tank made of glass fiber reinforced plastic (GRP), pressure-resistant up to 12 bar
  • Stable, non-slip base made of rubber
  • The connections are on the side and each have a quick-release coupling for the inlet and outlet, or directly via a ¾ thread
  • Head can be easily removed to change the used material
  • The cartridge is supplied filled and ready for use.
  • The cartridge supplies pure water with 0 µSiemens

The display is designed as a compact unit that is integrated into a distributor. You don’t have to connect it separately, simply plug it in with the quick connector – ready to go

It can also be reversed, which is practical and saves time when changing the resin.

The indicator has an in-built battery that lasts >5 years and does not require an external power supply. If it is necessary to change the battery, we will do it for you.

Green LED =

The water has the correct conductivity value of max. 10 µSiemes and can be used.

Yellow LED =

The resin is beginning to lose its ability to clean, the water can still be used, the resin should be changed soon

Red LED =

The conductivity is above 10µSiemens and should no longer be used.

Product order information

Deionizer cartridge Set, content4.7 Liter, Size "S"Article no. xxx xxx
Deionizer cartridge Set, content 7.0 Liter ,Size M“Article no. xxx xxx
Deionizer cartridge Set, content 12 Liter , Size L“Article no. xxx xxx

We offer all spare parts separately, please do not hesitate to contact us if you need anything additional.


Links:

  • Here you will find some literature on the further function of our demineralizer Click Here
  • How do I interpret the display ? Click Here
  • How can I change the resin? Click Here
  • Our resin change service Click Here